4 Tips For the Successful use of a Ferro Rod

I love spark rods. These durable, yet affordable spark throwers will work in any temperature extreme and even work after being wet. And while a butane lighter may work best in most situations (since an open flame ignites a wider range of tinder than sparks alone), a “Ferro rod” makes a great piece of backup gear. They’ve also been around for over a century. Ferrocerium was invented in 1903 by the chemist Carl Auer von Welsbach in Austria. This alloy produces hot sparks in excess of 3,000F when it’s scraped against a rough surface or sharp edge. The recipe for this alloy varies, but it’s generally 50 percent cerium, 25 percent lanthanum, 19 percent iron, with small amounts of praseodymium, neodymium, and magnesium.

Carl Auer von Welsbach 

Ferrocerium rods are a popular fire starter among survival enthusiasts, though quite often, they are sold in packaging that is devoid of detailed instruction. This knowledge gap leads to frustrated newbies and mistaken claims that the products don’t work. Over the years, I’ve watched fledgeling survivalists stumble over the same problems—which are easily solved with a little understanding.

1. Scrape Off The Paint

Many spark rods are coated with a slick black paint to prevent corrosion and to keep them from scraping against each other during manufacture and transport to the marketplace. This paint will need to be scraped off before the sparks start to fly. Most often, the pressure you’d apply to scrape off sparks will also scrape off the paint and expose the ferrocerium.

2. Scrape Hard

I often advise my students to scrape the rod “like you’re trying to break it!” Dainty scraping won’t remove enough material from the rod or provide enough friction to ignite the scrapings. Scrape it like you mean it!

3. Pick The Right Fuel

Spark rods don’t light everything on fire. You’ll need natural plant-based fuzz for the tinder on this ignition method. Cotton balls and dryer lint are great choices in the backyard, while cattail seed down, goldenrod fluff, and milkweed down are great materials to source in the wild. Dry, dead leaves and coarse wood shavings may also seem like a fit, but those usually won’t light with sparks alone. You’d typically need the open flame of a match or lighter to get them going.

4. Move the Rod, Not the Scraper

I often see beginners throwing more tinder around than sparks. Thankfully, there’s an easy way to correct that flawed technique. If you hold the scraper still and pull the rod away (imagine you’re pulling the cord to start a chainsaw or push mower) you won’t knock the tinder all over the place. You’ll still get your shower of hot sparks, without the destructive follow-through of the scraper.

3 Tips for Better Tinder

Tinder is the dead, dry plant-based material that is capable of turning a coal, ember or spark into a flame. Tinder is one of the foundation pieces for fire making, and you can often find excellent tinder in the form of grasses, leaves, pine needles, fibrous tree bark, weed tops, seed down, wood shavings, and more unusual stuff like palm fibre and certain mosses. Whatever you choose, these natural materials should have several things in common.

First, it should all be dead—but usually not rotten—plant based materials. Rotten plants usually lose more and more of their fuel value as they decompose. But there are always exceptions. Just remember ... dead plant-based materials.

Second, it should be as dry as it possibly can be. In rainy weather, this may mean finding a few scraps of tinder at a time, even one leaf at a time, and KEEPING the tinder dry while you search for more.

Finally, it should be light, airy and have a lot of surface area for its mass. In other words, it needs to be fluffy. Materials that are not fluffy should be processed in some way to increase their surface area so that they can reach their combustion temperature as quickly as possible.

Not every tinder type is “ready to use” when you find it in nature. It may be too coarse, too flat, or too solid to burn effectively. But with the right processing technique, we can change this vital material - increasing its surface area and enabling it to burn quickly and easily. Here are three ways you can get your materials in shape for fire starting.

1. Shred It

That’s right, tear it apart by hand! Start by tearing at large sections, and then tear the remainders into shreds. This technique works well for tree bark fibre (like tulip poplar, basswood, cedar, pawpaw and many others). You can also shred weed tops and seed down into a fluffier form.

2. Pound Away

Easy and therapeutic, pounding your tinder with a rock can separate the fibres nicely (and give you a constructive place to vent your rage). Most of the fibrous dead inner tree barks and plant stalk fibres work really well with this trick. Wad up the fibres into a ball or fold them into a linear bundle, and pound them with a rock or similar hard object. Turn the bundle often, and you’ll cover all of your surface area with no trouble. Pound your tinder on a hard log or a stone for best results. Keep working until your tinder has the desired fluffiness. If you don’t have a dry place to work, shred the tinder instead of pounding. By pounding on damp or wet surfaces, you’re driving moisture into the tinder and reducing its flammability.

3. Scrape and Scratch

When dealing with trees that have a fibrous outer bark (like cedar, cypress and juniper), you can use your trusty knife or even a sharp stone to scrape off fibrous tinder. This can even be done on live trees, without harming them. Just scrape off some of the fibrous outer bark, and collect the fuzz you remove. You can also scrape wood to make wood shavings if no other tinder is available (or dry).

Make the Most of Your Fire with a Reflecting Wall

Retain more heat from your fire with a fire wall.

The reflecting wall is a great structure to build in semi-permanent camps, and you can even build quick ones at overnight stopping points. These walls block some of the wind (when positioned correctly) and they reflect more of the heat of a fire back toward the user. When used in conjunction with a survival shelter, these walls can create a much more comfortable micro-climate by literally “fencing in” the heat. The wall can be any size or shape, and built from many different materials. Of course, bigger is better. And smoother walls reflect heat better than rough ones. But as long as you have something in place to reflect back lost heat, each stick you burn will make you feel warmer than you would feel without the wall.

Wooden Walls

Any wood can be used for a reflecting wall. If you’d like it to last, cut and stack green wood for your wall. The extra moisture of live wood will limit its flammability. If you’d like the wall to double as a firewood drying rack, you can build it from dead wood that is wet. Just pull out the sticks as they dry, throw them in the fire, and replace them with new wet pieces as you go. You could even use rotten wood to build your wall, if that’s all you have available. The bottom logs or poles that are closest to the fire will dry out and begin to burn first, unless you plaster them with mud, prop flat stones against them, or build the wall far enough away (about 1 yard) that it cannot burn. To build your wall, gather a pile of logs or poles, and drive two stout stakes into the ground. They should be closer together than the length of your shortest log. Set your thickest log on the ground, butted up against the two stakes, then drive in another pair of stakes to pin the log in place. If you plan a low reflecting wall, use stakes about a yard long and drive one foot into the ground. Go for longer stakes is you want a higher wall.

Stone and Mud Walls

For semi-permanent camps (or when stone is your most abundant resource), build a stone wall to bounce back the heat of a fire which would normally be lost. The rocks can be laid “dry” (without any mortar), or you can use mud or clay as a mortar substitute. Mixing dead grass with the mud will add additional strength to the mortar. And if enough mud and grass were available, you could even build your reflecting wall entirely from mud mortar (also known today as “cob”). Make it wider at the base for stability, insert sticks here and there for internal support, smooth the surface for heat reflection, and don’t go too high all at once. Top heavy mud walls tend to flop over.

A Note on Safety

For any rocks you plan to use near a fire, make sure you get your rocks from a dry location. It’s also smart to test them in a campfire (while you’re at a distance) to make sure they don’t explode. NEVER use rocks you collected by a waterway (high rate of explosion). Ever built a fire reflecting wall? Please share your results by leaving a comment.

5 Essential Bushcraft Knife Skills to Learn

The best bushcraft knife in the World will not guarantee it's going to be useful for you in the wilderness.  In order for it to be useful when it really counts,  you need to learn and practice some basic bushcraft knife skills.  In this article, I'm going to show you 5 knife skills that you can start working on today.

The great thing about learning to use your bushcraft knife is that you can do this in your backyard.  Thpractisinging is fun and over time you will become proficient with your bush knife.  Then if the need ever arises in the wilderness or a survival situation you will be prepared and know that you have chosen the right knife for the task.

Carving

Carving is probably going to be one main uses for your bushcraft knife.   This will allow you to make useful tools like spoons, bowls, and fire boards.  Carving is also something that is fun to practice at home and will greatly increase your overall control with your bushcraft knife.

You are also going to find out how well your bushcraft knife does at some of the smaller tasks.  Many people want a thick long blade for their main knife but those knives can suffer sometimes when it comes to the finer tasks like carving.

There are many knives made especially for carving like hook knives.  And while I use and suggest you have these knives as well, I also suggest you learn to do carving with your main bushcraft knife.  That way if the situation ever arises where it's the only knife on your person you know what to expect from that knife and your bushcraft knife skill set.

Batoning

Okay, I'm going to start right off by saying that batoning is controversial among bushcrafters.  Many believe that you shouldn't use your bushcraft knife for batoning, myself included.  I prefer to carry an axe, saw or hatchet to perform wood tasks around the camp.

However, I still feel like it's a skill you should learn and practice because you never know when the situation arises that you don't have an axe or hatchet.  It's better to be prepared and know whether or not your knife can handle the task of batoning when you are at home in your backyard than when you really need it.

Most of your batoning will be done in the form of splitting wood.  You will need to select a bushcraft knife that is a few inches longer than the wood you are trying to split. 

Place the wood on a solid surface standing on end.  Then place your knife on top of that.  Strike out towards the exposed tip of the knife with a small hard piece of wood (the baton).  Keep batoning the knife until you split the wood. 

Try not to hit directly on the tip to protect the knife if possible.  A thicker blade will usually give you better results when batoning and is less like to take damage.  Also, it's important to have a full tang knife blade when doing this to avoid breaking the knife from the handle or scales.

Besides splitting wood, you can also baton with your knife when truncating wood.  This is when you are cutting small diameter wood into shorter pieces.  The procedure is basically the same as splitting wood but instead of placing the wood on its end you are placing it on its side.

Finally, you can baton with your knife to make deeper notches in your wood (similar to a wood chisel) or to also cut off small branches.   Even though not everyone agrees on using their knife for batoning I would still recommend learning the skill and to make sure you have a knife that can hold up to this bushcraft knife skill.

Feather Sticks

Making feather sticks is an important bushcraft skill to learn with your knife.   Feather sticks will allow you to start a fire when wood is damp and other methods might fail.  They will provide quick and intense heat for your fire at the beginning.  Another thing is that by making feather sticks you will improve your other bushcraft knife skills.

A good method is using a light touch to make light slices in the wood.  This will give you nice curls in your feather stick.  By practising this skill you will see how well your knife's blade bevel and sharpness does with this common bushcraft tasks.

Practice this skill in conjunction with your carving and fire starting skill below.  In no time you will be able to make some impressive feather sticks and you will be prepared to light a fire in adverse conditions.

Fire Starting

Making a fire is paramount in survival situations or just general bushcrafting.  It's important to know if your knife can handle this task.  It's also easy to practice at home in your backyard.

One technique to practice is whether or not the spine of your bushcraft blade can ignite a ferrocerium rod.   The Ferro rod is an easy way to start a fire and can be used thousands of times over. 

In order to do this, you will need a knife with a good 90-degree spine in order to throw a good amount of sparks.  You may need to file the knife spine down to achieve this but it's definitely worth the effort.  A good shower of sparks could be the difference between getting a fire started and sleeping in the cold.

Another fire starting technique to learn is flint and steel.  This technique will only work with your knife if it has a carbon blade.  A stainless steel knife blade won't throw off a spark when struck with a piece of flint.   For this reason, many bushcrafters only use carbon knives.

As with all bushcraft skills, practising fire starting at home and often will make your proficient for those times when you need to get a fire started in the wild.  I also suggest practising not only with dry material but also wet material.  The same applies to cold and warm weather.  It's much easier to gain confidence on starting a fire in wet cold conditions knowing your house is just a few yards away.

Chopping

As if batoning wasn't' controversial enough, I give you chopping.   Many people like to use their bushcraft knife to chop down small trees to make shelters or tools around the camp.  This can be very hard on a knife blade and can loosen handle scales and damage knives.

I'm going to say the same thing here as I did with batoning in that it's a good bushcraft knife skill that you can learn at home.  You will know right away if your knife is good for this type of task. 

The most common method of chopping with a knife is getting out towards the end of the handle with your grip.  Some people only use 3 fingers to grip the handle which makes it easier to give the knife some swinging momentum when striking wood.  Just be careful that you still have a decent grip on the knife for your own safety and the safety of others.

You might also find after using your knife for batoning and chopping that it will work but isn't great for those tasks so you will instead choose to carry and axe, saw or hatchet into the woods.  Again better to learn that now that in a situation where you really need it.

Summary

You will notice that the theme of this article is to practice these skills at home before you are in a situation where your life may depend on it.  Not only will you find out what your bushcraft knife is capable of but you will also improve your own bushcraft skill set. 

An okay bushcraft knife is better in someone's hands with expert skills than a great bushcraft knife is in someone lacking good bushcraft knife skills.  By working at this you will become the former and it will be less stressful when you need these skills.

I hope this helped and please if you have any tips of your own, comment with your thoughts below

What Do You Think Of The History Channel's Show "Alone?"

I'm curious, what do you all think of The History Channel's  show "Alone?" All the contestants appear to be Youtube guys, which makes sense since they have more experience with video, etc. I have great respect for them putting themselves out there like that. But many seemed to not have much experience spending time alone in the woods considering they are billing themselves as survival experts. After just a day or two, some were crying on camera. One couldn't make fire with fatwood, which is waterproof and burns in the rain. Many could not get a fire going after several days, unaware of how to dry tinder inside a jacket.

Still, I think it is an entertaining show and shows the harsh reality of life in a survival situation. I do think it's overzealous that History branded all of them as "survival experts" just because they have Youtube channels. Some of these guys obviously have good skills and are entertaining to watch, but some have padded their resumes a bit, or else History did it for them. Had they not been represented as survival experts, I would say most of them have done a great job so far. 

Maybe History Channel should just remove the "expert" moniker and then the show would better represent itself. I think many people have grown weary of survival shows misrepresenting themselves in this manner. What do you think?

Leave a comment below or join the discussion on Facebook

3 Handy Tips for Ferrocerium Rods

Ferrocerium rods are a favourite fire starter among many outdoor and survival enthusiasts. Ferrocerium is a man-made metallic material that produces sparks in excess of 3,000 degrees Fahrenheit when it’s scraped with a rough surface or a sharp edge. The ferrocerium recipe varies by manufacturer, but it’s generally 50 percent cerium, 25 percent lanthanum, and 19 percent iron, with small amounts of praseodymium, neodymium, and magnesium. The most common use of this material is as the flint in cigarette lighters. And while a butane lighter may work best in most fire-starting situations, a “Ferro rod” makes a great back-up. Here are three things to keep in mind when using a Ferro rod to start a fire.

Pick The Best Tinder: It might seem odd to use natural plant fuzz as tinder, but it is truly one of your best choices for getting a flame started, and works as well as cotton balls or dryer lint. These fibrous and fluffy materials of botanical origin are the perfect fuel to allow the sparks to “stick” and begin burning. Cattail seed down, goldenrod fluff, and milkweed down are among my favourites to use. Just collect a little bit when it’s dry, and store it in a water-tight container for use in fire starting.

Move The Rod, Not The Scraper: Rather than pushing the scraper against the rod toward your tinder, pull the rod across the scraper toward yourself. You’ll still provide a hot shower of sparks, but avoid knocking your tinder all over the place with your follow-through.

In The Deep Cold: Can’t get your butane lighter to work at 10F? That’s because butane will begin to gel once temperatures get into the teens. If the butane gels, you may be able to warm it up by placing it inside your clothing for a while. Or you could just move to your ferrocerium rod, which is unaffected by temperature extremes, and even works when wet.

How do you use your Ferro rods? Let me know your method by leaving a comment.

Fire Pits, Mounds, and Platforms

Fire is one of our best friends in a wilderness emergency, and we need to plan accordingly for it. When it’s time to set up a fireplace, you’ll need to figure out exactly where and how to build it. Some conditions require a mound underneath your fire, while other circumstances demand a fire pit. And in a few situations, the fire has to be on a platform in order to burn at all. Here are some of the conditions in which to use each.

Fire Pits

These are the most common places to build and maintain a fire. Most fire pits are circular, dish-shaped depressions or holes. They can be almost any size or depth, depending on the size of the fire you need. These depressions cradle the fire, grouping the coals in the center to help them burn longer and hotter. You don’t want to make the hole so deep that it keeps in all the heat, unless you’ve had to build a fire under very windy conditions. For this case, you’ll want to create a Dakota fire hole. This is a Native American fireplace style which burns wood efficiently like a wood stove; and it provides a greater margin of fire safety by keeping coals and flames fairly contained in windy conditions. This setup involves two holes in the ground with a tunnel connecting them at the bottom. The “upwind” hole stays empty and acts as a funnel to catch the wind. The fire burns in the “downwind” hole, relatively safely.

Fire Mounds

In wetter climates, or in areas prone to sudden downpours of rain, the fire mound makes a lot of sense. Fire pits can easily fill with water and drown your coal bed. When this happens, your fire is doomed. The ancient forebears to the Seminole natives started using simple mounds of sand to keep their fires going in the wet and swampy terrain of the American southeast. This technique is still in use there today. Fire mounds can be made from almost any non-flammable material: Sand, soil, mud and stone can all be used to give you a mound for a high and dry fireplace. Build the mound as tall as you need, from a few inches to a foot tall.

Fire Platform

Burning a fire on top of the snow is often one of those things that you never really think about until you have to do it. In areas with little snow, you can always dig down to the soil surface to build your fire. But if the snow is very deep, or you lack digging tools, fire on top of the snow is the best option. Less experienced outdoor enthusiasts often get a rude shock the first time they try burning a fire directly on the snow. The fire starts out normally enough. Then the snow melts, which puts out your coals and leaves you with no fire and a jumble of wet, black sticks. To solve this problem, you’re going to need a platform. This can be a manmade material such as a piece of metal for a platform. You’ll just need some logs or rocks under it, so the metal doesn’t melt the snow underneath. If you don’t have metal, the platform can be made of dead wood, rotten wood or green wood. This last choice is the best, because the live wood has enough moisture in it to keep it from burning for a few hours, but not so much moisture that it puts out your burning sticks or bed of coals. You can use whole chunks of wood or split the wood in half to create a very flat platform. Obviously, the whole pieces will last longer than split wood. Replace the raft as needed.